Digikeijs DR5000-ADJ DCC multi-bus central command station

DR5000 features and connections

USB

• Communication with computer/control program
• Protocol L.NET or XpressNet V3
• Virtual COM-port, speed 9600, 19200, 38400, 56800 of 115200 Baud
• Firmware updates

L.NET T

• Interface for L.NET devices (Controllers, Feedback modules etc.)

L-NET B

• Interface for L.NET devices: (manual) Controllers, Feedback modules etc. Max 12v/1000mA power
• Interface for L.NET devices including boosters (rail-sync). Max 12v/600mA power

X-BUS/R-BUS

• Interface for XpressNet devices: MultiMaus, LH100 etc. Max 12v/1000mA power
• Interface for R-BUS feedback modules.

B-BUS

• Interface for ROCO Boosters, e.g. the MultiMaus boosters 10764 lan as a booster together with the DR5000!

RS-BUS

• Interface for Lenz-RS-Bus feedback modules

ext88N

• Interface for s88N feedback modules. Max 16 x 16 input modules (256 inputs)
• Interface for DR502xEXT modules (bi-directioneel).

Track-Output

• DCC rail-output. Max 19V/3.2Amp. Lower voltages by other power supply. Min 14V.

Program-Track

• DCC programming output. Max 19V/800mA.
• Automatically switches from Track-Out to Program mode so the programming rail can also be used.

LAN

• 100baseT Ethernet. Can be connected to a local network via DHCP.

WiFi/WLAN

• bgn Wireless network via internal antenna
• Both networks can be accessed via UDP / IP and TCP / IP
• Protocols: Lenz XpressNet and/or L.NET-TCP/IP
• Wifi/LAN settings can be changed via a web-interface
• The WiFi / LAN module can serve as an AP (access point) as well as a router between the DR5000 and WiFi home network (LAN).

Control

• ‘Stop’ button to disable track output
• ‘Go’ button to enable track output

IR-Throttle

• IR receiver compatible with Uhlenbrock IRIS and Piko DigiFern (or other RC5/36Khz remotecontrols)
• 4 channels, per channel directly to be controlled/switched, 1 loco and 4 switches
• Further control possible through X-BUS and/or L.NET (manual)controls, the DR502xEXT modules or via the USB/LAN/Wifi interfaces.

LEDs

STATUS

• Power: Power supply present; Programming track indicator
• Load: Output load. Intensity is increased with the load, off = no load, on is 3.15Amp
• Short: Short circuit. Blink Code defines the bus causing the short circuit. Continously on is Track-Out

USB

• TX: Data is sent to the computer
• RX: Data is received from the computer.

INFRARED

• RX: Valid IR data is being received.

X-BUS

• TX: Data is being send to the X-BUS
• RX: Data is being received from the X-BUS.

STOP

• The signals to Track-Out and the booster connection are off.

GO

• The signals to Track-Out and the booster connection are ON.

L.NET

• TX: Data is sent to the L.NET
• RX: Data is being received from L.NET

ext88

• There is at least one input on the s88 bus active
• Intensity increases with the number of active inputs.

WiFi

• Active: The Wifi Network is active.

LAN

• Link: The LAN is connected and connected to a switch / hub / router.

ROUTER

• Status: The internal router is active.

DCC

Locos

• 126 simultaneous operation / control of locos
• Full function key assignment F0 – F28
• 14/28/128 speed steps
• Long and short addresses. (9999 for long, Maximum short addresses to be set from 0-127)

Switches

• 2048 switches
• Offset +4/-4 for MultiMaus compatibility

Feedback

2048 feedback indications, which is the total of all possible buses. A smaller maximum could occur per bus. Feedbacks from combining all buses in one series of 1-2048

Power Supply

Includes a modern low-loss switching and adjustable external power supply (15 – 24 Volt).